WhatsApp : +88 01818929292 / +8801730296909
info@smmarineservice.com sohelbhuiyan1213@gmail.com
WhatsApp : +88 01818929292 / +8801730296909
info@smmarineservice.com sohelbhuiyan1213@gmail.com
Product Image Product Image Product Image
Product Image
Product Image
Product Image

Honeywell Enraf 32269 Assembled Probe for LIDEC L20-70D Water Ingress & Level Detector (New)

Item Code:

32269 / L20-70D

Brand:

HONEYWELL ENRAF MARINE

Condition:

New product


Honeywell Enraf 32269 Assembled Probe for LIDEC L20-70D Water Ingress & Level Detector (New)

Product Information

Manufacturer Honeywell Enraf Marine (Honeywell Marine SAS, formerly Enraf Marine Systems, France)
Marking on Probe ENRAF – P/N: 32269 – SN: 2970
Part Number 32269 (Assembled Probe)
Used In LIDEC L20-70D level switch / level detector (also the L20-70DR relay version)
Product Type Water ingress / liquid level detection probe with connecting cable
Probe Material Stainless steel 316L
Cable Black multi-core cable, three conductors (brown, blue, red) with ferrule ends
Cable Length Not clearly visible in the supplied photograph
Condition New
Supplier SM MARINE SERVICE™

Product Introduction

The Honeywell Enraf P/N 32269 is the assembled sensing probe of the LIDEC L20-70D level detector, a fixed marine alarm sensor made by Honeywell Marine (formerly Enraf Marine Systems) in France. The probe is the part that sits inside the cargo hold, bilge, pump room or tank and senses when liquid touches its stainless steel tip. SM MARINE SERVICE™ supplies this probe as a new replacement spare for ships worldwide through https://www.smmarineservice.com/.

What Is This Equipment?

LIDEC (Liquid Detector) L20-70D is a point level switch with no moving parts. Its main use on ships is the Water Ingress Detection System (WIDS) in the cargo holds of bulk carriers, and the pump room alarm system (PRAPA) on tankers. A complete detector has three parts: this probe (32269) with its cable, an electronic board inside a connecting box (polyester or stainless steel), and the power supply / alarm panel on the bridge or in the control room. When the probe alone is damaged – for example by cargo impact, corrosion of the cable or sandblasting – only the probe needs to be replaced.

Main Features

  • Genuine Enraf assembled probe, marked P/N 32269
  • Stainless steel 316L probe body, suitable for hold, bilge and tank environments
  • Works on the surface-wave principle – no float, no moving parts, nothing to stick
  • Not affected by dry bulk cargo such as coal or cement; works even when cargo absorbs water and turns into a paste
  • Fail-safe alarm: liquid contact, sensor fault, electronics fault or power loss all give an alarm
  • Horizontal or vertical mounting
  • Intrinsically safe design for hazardous areas when used with the matching LIDEC board and barrier

Honeywell Enraf 32269 assembled probe with cable for LIDEC L20-70D water ingress detector - SM MARINE SERVICE
Honeywell Enraf P/N 32269 assembled probe with cable for LIDEC L20-70D (new) – SM MARINE SERVICE™

Main Technical Specifications

Values below are for the complete LIDEC L20-70D detector as given in the Honeywell Marine manual NT406E; they apply when this probe is used with the original LIDEC board.

Measuring principle Piezoelectric ceramic generating mechanical (surface) waves in the metal probe
Power supply 16 to 28 VDC (24 VDC nominal), approx. 0.6 W
Output (L20-70D) Current loop 18 mA / 6 mA (some data sheets state 20 mA dry / 7 mA wet)
Output (L20-70DR) Dry contact relay COM/NO/NC, 5 A at 28 VDC
Accuracy / hysteresis ±2 mm / less than 4 mm
Alarm point Vertical mounting: 5 mm above the low point of the probe; horizontal mounting: probe axis
Probe-to-box cable Up to 30 m
Protection Probe IP68 (tested at 50 m depth); connecting box IP66 / IP66-67
Temperature Probe up to +70 °C; housing −25 to +70 °C; storage −40 to +80 °C
Hazardous area II 1 G D Ex ia IIC / IIB, T6–T4 (LCIE 02 ATEX 6181X, IECEx LCI 11.0001X)

Inside the Unit: PCBs, Modules & Part Numbers

The probe 32269 works together with the following LIDEC parts. These numbers are listed so engineers can match their existing system:

32269 – Assembled Probe

Stainless steel sensing probe with cable (brown, blue and red wires). This is the product on this page.

M12027 – Current Output Board (without test switch)

Electronic board for the L20-70D current-loop version; drives and reads the probe and gives the 18/6 mA signal.

34231 – L20-70D WIDS LIDEC PCB Current Output

Current output PCB listed for the L20-70D used in Water Ingress Detection Systems.

25789 – Dry Contact Output Board

Relay output board used in the L20-70DR version.

M11979 – Current Output Board

Enraf current output board listed together with 32269 by some spare-parts traders. Not verified for L20-70D.

22279 – Cable 3 x 0.75 mm², OD 7 mm

Three-core cable listed among the same Honeywell Enraf marine fixed spares. Not verified as the exact cable fitted to this probe.

Main Components & Related Units

  • M31999 – L20-70D (current output) in polyester connecting box
  • M34227 – L20-70D (current output) in stainless steel box
  • M32017 – L20-70DR (relay output) in polyester box
  • M36114 – L20-70DR (relay output) in stainless steel box
  • M34229 – L20-70D dual stainless steel box with test switch
  • L20-70D-S – level detector assembly (probe + PCB + junction box) as marked on some vessels
  • Zener barrier / power supply and alarm panel of the Water Ingress Detection System

Marine & Industrial Applications

  • Water Ingress Detection System (WIDS) in cargo holds of bulk carriers (SOLAS XII)
  • Pump room bilge and pump alarm systems on oil and chemical tankers (PRAPA)
  • Bilge high-level alarms, void spaces, cofferdams and ballast spaces
  • High-level and overfill alarm points in tanks
  • Industrial sumps and pits where a robust point level switch is needed

Enraf P/N 32269 SN 2970 probe marking close-up L20-70D LIDEC level detector - SM MARINE SERVICE
Close-up of the probe marking: ENRAF P/N 32269, SN 2970

Common Problems & Troubleshooting

  • No detection: check the wiring between probe and board and the supply voltage (16–28 VDC).
  • Loop current above 19 mA: the board may be set for relay output instead of current output – check the board settings.
  • Constant alarm in a dry hold: check for cargo residue or dried paste on the probe tip, damaged cable or water inside the connecting box.
  • Function test: squeeze the probe tip between your fingers – the output should change (relay release or current change).
  • Safety: switch off power before any connection work, keep the intrinsic-safety barrier in place, and never paint the probe.

Maintenance Tips

  • Clean the probe periodically, especially after viscous or sticky cargo.
  • Protect the probe from shocks, sandblasting and paint during hold maintenance.
  • Only fine-tune with the "SENS" potentiometer on the board; red-varnished potentiometers are factory set.
  • Earth the cable screen at the supply side only.
  • Test each detector regularly as required by your planned maintenance system and class.

Spare Parts & Replacement Availability

SM MARINE SERVICE™ supplies the Enraf 32269 probe and related LIDEC L20-70D spare parts. For a fast quotation, please send the part number (32269), the type label of your detector box (for example L20-70D, L20-70DR, M31999), the serial number and the vessel name. A photo of the label helps us confirm the correct replacement.

Worldwide Supply & Shipping

We supply marine spare parts to ship owners, ship managers and repair yards across the Middle East (Dubai, Fujairah, Jeddah, Doha), Europe (Rotterdam, Hamburg, Piraeus, Istanbul), Asia (Singapore, Shanghai, Busan, Mumbai, Jakarta), the Americas (Houston, Panama, Santos, Buenos Aires, Callao) and Africa. Parts can be shipped by courier to the vessel's agent or to our customer's office.

Why This Equipment Is Still Used

Thousands of bulk carriers and tankers were fitted with Enraf / Honeywell LIDEC detectors. The design has no moving parts and is not disturbed by dry cargo, so ship owners keep the existing system and replace only the failed probe or board instead of changing the whole Water Ingress Detection System.

FAQ

What is Enraf P/N 32269?
It is the assembled probe of the Honeywell Enraf LIDEC L20-70D level detector.

Is 32269 the same probe for L20-70D and L20-70DR?
The LIDEC manual lists probe 32269 for the L20-70D family; please confirm your box label with us before ordering.

Can I replace only the probe?
Yes. If the board and box are working, only the damaged probe needs to be changed.

Does the probe need calibration?
No calibration is normally required; the alarm point is factory set.

What signal does the L20-70D give?
A current loop of 18 mA when dry and 6 mA when liquid is detected (fail-safe).

What PCB is used with this probe?
The current output board M12027 (L20-70D) or the dry contact board 25789 (L20-70DR); 34231 is also listed as an L20-70D WIDS current output PCB.

Can it be mounted horizontally?
Yes, the probe can be mounted horizontally or vertically.

Is this probe new?
Yes, the probe shown on this page is new.

Do you ship worldwide?
Yes, SM MARINE SERVICE™ ships marine spare parts worldwide.

Short Product Description

New Honeywell Enraf P/N 32269 assembled probe for the LIDEC L20-70D level detector. The stainless steel 316L probe uses the surface-wave principle to detect water or liquid without any moving parts, and is widely used in Water Ingress Detection Systems (WIDS) of bulk carrier cargo holds and in tanker pump room alarm systems. It works with the L20-70D current output board (M12027) and the L20-70DR relay version. Supplied with cable (brown, blue and red wires) by SM MARINE SERVICE™, a worldwide supplier of marine automation, navigation and tank gauging spare parts.

Related Honeywell Enraf Tank Gauging & Level Sensors – In Stock at SM MARINE SERVICE™

SM MARINE SERVICE™ – Marine Automation & Navigation Equipment Supplier

Available Equipment Conditions: New • Used • Refurbished • Reconditioned (Specific product condition and availability are subject to confirmation.)
Stock Locations: Bangladesh • China
Services: Worldwide Shipping • Technical Support • Spare Parts Supply • Marine Equipment Sourcing
Samir Market, DT Road, Pahartali, beside CDA Market, Chattogram, Bangladesh
Mobile / WhatsApp / Viber: +88 01818 929292
Email: info@smmarineservice.com
Website: https://www.smmarineservice.com/

Need the Enraf 32269 probe or other LIDEC L20-70D spares? Send us your part number and vessel details today for a quick quotation.


Related products

Seres ODME MK III Oil Discharge Monitoring Equipment Control Unit

BDT 0

Seres ODME MK III Oil Discharge Monitoring Equipment Control Unit

BDT 0

Seres ODME MK III Oil Discharge Monitoring Equipment Control Unit

BDT 0

KONGSBERG GT404D4H25T Pressure Transmitter | GT404 25 Bar Marine Cargo Line & Manifold Pressure Sensor

BDT 0

SM Marine Service

SM Marine Service

Marine Equipment Supplier

Welcome to SM Marine Service! How can we help you today? 9:46 PM
Need Help? Chat with us