WhatsApp : +88 01818929292 / +8801730296909
info@smmarineservice.com sohelbhuiyan1213@gmail.com
WhatsApp : +88 01818929292 / +8801730296909
info@smmarineservice.com sohelbhuiyan1213@gmail.com
Product Image Product Image Product Image
Product Image
Product Image
Product Image

New Waukesha ESM 740824C ECU Module – Dresser Engine Control Unit

Item Code:

740824C

Brand:

Waukesha (Dresser)

Condition:

New product


New Waukesha ESM 740824C ECU Module – Dresser Waukesha Engine Control Unit

Product Information

Product Name ESM Engine Control Unit (ECU)
Manufacturer Waukesha Engine, Dresser, Inc. (brand now INNIO Waukesha)
System Waukesha ESM (Engine System Manager)
Waukesha Part Number 740824C
ECU Serial Number 02480 (as printed on the label of one supplied unit); second unit: not clearly visible in the supplied photograph
Input Voltage 12–36 VDC
Maximum Current Draw 0.7 A
Maximum Temperature 160°F (70°C)
Manufacturer Address (label) 1101 West St. Paul Avenue, Waukesha, WI, USA 53188-4999
Condition New
Category Accessories (Control Modules & Parts)
Supplier SM MARINE SERVICE™

Product Introduction

The Waukesha ESM 740824C Engine Control Unit (ECU) is the central electronic control module of the Waukesha Engine System Manager (ESM), built by Waukesha Engine, Dresser, Inc. for Waukesha spark-ignited gas engines. It is used on gas engines driving generators and compressors in power plants, oil and gas facilities, offshore installations and marine/industrial service.

SM MARINE SERVICE™ (https://www.smmarineservice.com/) supplies the Waukesha ESM ECU 740824C as a new replacement module, together with related ESM spare parts, for customers worldwide. Send us the part number and the photo of your nameplate and we will confirm compatibility and availability.

What Is This Equipment?

The ESM ECU is the "hub" of the Waukesha ESM system. The whole ESM system interfaces with the ECU, and based on its inputs the ECU logic drives all subsystems. The ESM integrates spark timing control, speed governing, knock (detonation) detection, start-stop control, diagnostic tools, fault logging, engine safeties and air/fuel ratio control on supported engines.

The ECU is a sealed module with five connection points. On this unit the connections are labelled Service Interface, Power/Outputs, Customer Interface, Sensor Input A (non-incendive) and Sensor Input B (non-incendive). Three status LEDs on the front cover show Power, Alarm and Shutdown.

Main Features

  • Central control module of the Waukesha ESM engine management system
  • Spark timing control, speed governing and knock/detonation detection
  • Start-stop control, engine safeties and shutdown protection
  • Fault logging and diagnostics through the PC-based Electronic Service Program (ESP)
  • Wide 12–36 VDC input supply, low 0.7 A maximum current draw
  • Rugged sealed enclosure for engine-mounted service
  • Hazardous-area markings: CE, Ex II 3 G, EEx nA II T4 X, -20°C ≤ Ta ≤ 70°C; CSA certified Class I, Groups A, B, C, D, Div. 2, T4
  • Power / Alarm / Shutdown status LEDs for quick on-site checks

New Waukesha ESM 740824C ECU engine control module Dresser - SM MARINE SERVICE

Waukesha ESM Engine Control Unit (ECU), Part Number 740824C – new unit supplied by SM MARINE SERVICE™

Main Technical Specifications

Model / Part Number Waukesha ESM ECU 740824C
Input Voltage 12–36 VDC
Maximum Current Draw 0.7 A
Maximum Temperature 160°F (70°C)
Ambient Range (Ex marking) -20°C ≤ Ta ≤ 70°C
ATEX / IEC Marking CE, Ex II 3 G, EEx nA II T4 X
CSA Certification Class I, Groups A, B, C, D, Division 2, T4
Connections Service Interface, Power/Outputs, Customer Interface, Sensor Input A, Sensor Input B
Indicators Power, Alarm, Shutdown LEDs
Dimensions / Weight Not clearly visible in the supplied photograph
Software / Firmware Version Not clearly visible in the supplied photograph

Inside the Unit: PCBs, Modules & Part Numbers

The Waukesha ESM ECU is documented by the manufacturer as a sealed module. Waukesha does not publish separate field-replaceable PCB or card numbers for the inside of the ECU – the complete unit is serviced and replaced by its part number. The information below lists what is verified.

ECU Main Assembly – Part Number 740824C

Function: complete engine control electronics of the ESM system (ignition timing, governing, knock detection, safeties, logging). Part number taken from the unit label.

Internal PCB / Board Numbers

Not verified – no internal PCB numbers are published by the manufacturer for this sealed unit. If you need a board-level repair, send us photos of the board markings and we will check them for you.

Main Components & Related Units

The Waukesha ESM system around the ECU includes the following units (part numbers are given only where found in a source):

  • Ignition Power Module with Diagnostics (IPM-D) – receives the ECU signal and fires the spark plugs at dual (normal/high) energy levels. Part number: Not verified.
  • Electronic Service Program (ESP) – PC-based software for programming, monitoring and fault logging.
  • Power Distribution Box / Junction Box (PDB) – power distribution for the ESM system. Part number: Not verified.
  • Electric throttle actuator / governor actuator and knock sensors
  • Magnetic pickups, oxygen sensors, temperature and pressure sensors
  • Harness for crankshaft pickup – Waukesha P/N A740749
  • Harness for camshaft pickup – Waukesha P/N A740750
  • Harness, electric start – Waukesha P/N 740744
  • Harness, ground, left bank to right bank – Waukesha P/N 740753
  • Flange ignition coil (for use with ESM) – Waukesha P/N 69694F
  • Injection Control Unit (ICU), APG engines – Waukesha P/N 740828
  • ESM2 – later generation with HMI industrial PC touch-screen panel

Marine & Industrial Applications

  • Waukesha VHP gas engines (e.g. 7042/7044, 5794, 9390/9394 series)
  • Waukesha VGF gas engines (F18, H24, L36, P48 series)
  • Waukesha APG 1000 (16V150LTD) generator engines and 275GL+ engines
  • Gas compressor packages in oil & gas fields and pipelines
  • Gas-engine generator sets for power plants, offshore platforms, FPSOs and industrial sites

Two new Waukesha ESM 740824C ECU modules - SM MARINE SERVICE

Waukesha ESM ECU 740824C units – new modules from SM MARINE SERVICE™

Common Problems & Troubleshooting

  • No Power LED: check the 12–36 VDC supply at the Power/Outputs connector and the power distribution box fuses and wiring.
  • Alarm LED on: connect the ESP software through the Service Interface and read the fault log to identify the sensor or circuit at fault.
  • Shutdown LED on / engine trips: review the logged shutdown reason in ESP (safety, overspeed, sensor fault) before resetting.
  • Knock or ignition faults: inspect knock sensors, IPM-D, ignition coils, spark plugs and harnesses.
  • Intermittent faults: check connector pins for corrosion, moisture and loose locking rings.

Safety note: disconnect all power before connecting or servicing any part of the electrical system. Ignition components can store high energy. Work in hazardous areas only according to site rules and the equipment certification.

Common Alarms

Specific ESM alarm and fault codes are read through the Electronic Service Program and are listed in the Waukesha ESM operation manual for your engine model. We do not list codes here without verification – please contact us with the code shown on your system.

Maintenance Tips

  • Keep connectors clean, dry and fully locked.
  • Check supply voltage and grounding regularly.
  • Download and keep the ESP fault log and calibration before replacing the ECU.
  • Protect the unit from excessive heat – maximum 70°C.
  • Keep a tested spare ECU on site for critical generators and compressors.

Spare Parts & Replacement Availability

SM MARINE SERVICE™ supplies the Waukesha ESM ECU 740824C and related ESM parts. For a quick quotation please send:

  • Part number (740824C) and a photo of the label/nameplate
  • Engine model and serial number
  • Quantity and required condition (new, used, refurbished)
  • Delivery port or address

We ship worldwide to ships, ports, rigs and industrial sites.

Why This Equipment Is Still Used

Thousands of Waukesha VHP, VGF and APG gas engines with ESM controls are still running in power generation and gas compression. Replacing a failed ECU with a compatible 740824C unit is much faster and cheaper than a full control-system upgrade, so replacement ESM ECU modules remain in strong demand.

FAQ

1. What is Waukesha part number 740824C?
It is the Waukesha ESM Engine Control Unit (ECU) made by Waukesha Engine, Dresser, Inc.

2. Which engines use the ESM ECU?
Waukesha gas engines with the ESM system, such as VHP, VGF and APG series engines. Please confirm with your engine documentation.

3. What supply voltage does the 740824C need?
12–36 VDC, with a maximum current draw of 0.7 A.

4. Does the ECU contain replaceable PCBs?
The ECU is a sealed module; Waukesha does not publish internal PCB numbers. It is normally replaced as a complete unit.

5. Can I search by PCB number to find this unit?
Yes – if you have a board number from inside a unit, send it to us and we will check it.

6. What software is used with the ESM ECU?
The PC-based Waukesha Electronic Service Program (ESP), connected through the Service Interface.

7. What do the Power, Alarm and Shutdown LEDs mean?
They show supply power, an active alarm, and an engine shutdown condition.

8. Is the ECU approved for hazardous areas?
The label shows Ex II 3 G, EEx nA II T4 X and CSA Class I, Div. 2, Groups A, B, C, D, T4.

9. Which other ESM parts can you supply?
IPM-D, harnesses (A740749, A740750, 740744, 740753), ignition coil 69694F and other ESM units on request.

10. What condition is this unit?
This listing is for a new unit. Other conditions are subject to confirmation.

11. Do you ship worldwide?
Yes, SM MARINE SERVICE™ ships worldwide.

Short Product Description

The Waukesha ESM 740824C Engine Control Unit (ECU) is the central control module of the Waukesha Engine System Manager, manufactured by Waukesha Engine, Dresser, Inc. It manages ignition timing, speed governing, knock detection, start-stop control, engine safeties and fault logging on Waukesha spark-ignited gas engines. The unit runs on 12–36 VDC with 0.7 A maximum current draw, carries Ex II 3 G and CSA Class I Div. 2 markings, and has Service, Power/Outputs, Customer and two Sensor Input connections with Power, Alarm and Shutdown LEDs. SM MARINE SERVICE™ supplies this ECU as a new module with worldwide shipping.


SM MARINE SERVICE™ – Marine Automation & Navigation Equipment Supplier

Available Equipment Conditions: New • Used • Refurbished • Reconditioned (Specific product condition and availability are subject to confirmation.)

Stock Locations: Bangladesh • China

Services: Worldwide Shipping • Technical Support • Spare Parts Supply • Marine Equipment Sourcing

Samir Market, DT Road, Pahartali, beside CDA Market, Chattogram, Bangladesh

Mobile / WhatsApp / Viber: +88 01818 929292

Email: info@smmarineservice.com

Website: https://www.smmarineservice.com/

Contact SM MARINE SERVICE™ today for a quotation on the Waukesha ESM 740824C Engine Control Unit.


Related products

Seres ODME MK III Oil Discharge Monitoring Equipment Control Unit

BDT 0

Seres ODME MK III Oil Discharge Monitoring Equipment Control Unit

BDT 0

Seres ODME MK III Oil Discharge Monitoring Equipment Control Unit

BDT 0

KONGSBERG GT404D4H25T Pressure Transmitter | GT404 25 Bar Marine Cargo Line & Manifold Pressure Sensor

BDT 0

SM Marine Service

SM Marine Service

Marine Equipment Supplier

Welcome to SM Marine Service! How can we help you today? 9:58 PM
Need Help? Chat with us