WhatsApp : +88 01818929292 / +8801730296909
info@smmarineservice.com sohelbhuiyan1213@gmail.com
WhatsApp : +88 01818929292 / +8801730296909
info@smmarineservice.com sohelbhuiyan1213@gmail.com
Product Image Product Image Product Image
Product Image
Product Image
Product Image

Sperry Marine NAVIGAT 2100 CDU Type 4995-AA – Fiber-Optic Gyrocompass Control and Display Unit (STO 074820, Refurbished)

Item Code:

4995-AA

Brand:

Sperry Marine

Condition:

Refurbished


Sperry Marine NAVIGAT 2100 CDU Type 4995-AA – Fiber-Optic Gyrocompass Control and Display Unit (STO 074820, Refurbished)

Manufacturer Sperry Marine (Northrop Grumman Sperry Marine)
System NAVIGAT 2100 Fiber-Optic Gyrocompass and Attitude Reference System
Product Control and Display Unit (CDU)
Type 4995-AA
STO No. (stock number) 074820
Revision REV C
Serial No. 0805002
Rear label NAVIGAT 2100 CDU 4995
Front sticker 0735-08 (meaning Not verified)
Connection Multi-pin D-sub connector on the rear, earth (ground) stud
Condition Refurbished

Product Introduction

The Sperry Marine NAVIGAT 2100 CDU Type 4995-AA is the operator panel of the NAVIGAT 2100 fiber-optic gyrocompass. From this unit the officer reads the heading, acknowledges alarms, confirms speed and position after alignment and changes the settings of the system. SM MARINE SERVICE™ supplies this control and display unit in refurbished condition, together with other gyrocompass spare parts. Visit https://www.smmarineservice.com/ for more navigation equipment.

What Is This Equipment?

The NAVIGAT 2100 is a fiber-optic gyrocompass – it has no spinning gyro and no moving parts. The system is built from three main units: the fiber-optic sensor unit, the Interface and Power Supply Unit (IPSU) and this Control and Display Unit (CDU). The Sperry Marine operation manual 056294 states that it applies to NAVIGAT 2100 systems with the control and display unit type 4995. The CDU shows heading and status data on its LCD screen and sends the operator's commands to the system. Each time the fiber-optic sensor is restarted, the operator must check and confirm the speed and position data on the CDU, otherwise the system will not enter normal operation.

Main Features

  • LCD screen marked "Control and Display Unit"
  • Three soft keys beside the screen for menu selection
  • ACK key for alarm acknowledgement and MENU key
  • Arrow keys with central ENTER key
  • Function keys F1, F2, F3 and DIM–/DIM+ for screen brightness
  • Black front panel with two mounting points for console installation
  • Rear multi-pin D-sub connector and earth stud
  • Northrop Grumman / Sperry Marine nameplate: STO No 074820, Type 4995-AA, REV C

sperry marine navigat 2100 cdu 4995-aa gyrocompass control and display unit

Sperry Marine NAVIGAT 2100 Control and Display Unit – front panel with LCD, ACK, MENU, ENTER, F1–F3 and DIM keys

Main Technical Specifications

Unit NAVIGAT 2100 Control and Display Unit (CDU)
Type / STO No. 4995-AA / 074820
Revision / Serial REV C / 0805002
Display LCD (size and resolution Not verified)
Keys 3 soft keys, ACK, MENU, 4 arrows + ENTER, F1, F2, F3, DIM–, DIM+
Rear connection Multi-pin D-sub connector, earth stud
Supply voltage Not verified – supplied from the NAVIGAT 2100 system
Dimensions / weight Not verified
Manual NAVIGAT 2100 Operation, Installation and Service Manual 056294

Inside the Unit: PCBs, Modules & Part Numbers

Sperry Marine does not publish board part numbers for the CDU in the documents we could check. The boards below are the normal parts of this unit; their individual numbers are marked "Not verified". If you need a board number, send us a photo of the label on your board.

CDU main / processor board

Runs the CDU software, drives the screen and handles communication with the NAVIGAT 2100 system. Part number: Not verified.

Interface / connector board

The green PCB visible behind the rear D-sub connector – carries the data and supply lines from the system into the CDU. Part number: Not verified.

LCD display module and backlight

Shows heading, menus and alarm messages; brightness is set with DIM–/DIM+. Part number: Not verified.

Keypad / membrane keyboard

Front keys ACK, MENU, ENTER, arrows, F1–F3, DIM and the three soft keys. Part number: Not verified.

Software / program memory

CDU firmware stored on the main board. Software version: Not verified.

Main Components & Related Units

  • NAVIGAT 2100 fiber-optic sensor unit – measures heading and rates.
  • NAVIGAT 2100 IPSU (Interface and Power Supply Unit) – power supply and data interfaces; the manual lists its AC input terminal block TB9, line filter FL1 and power transformer terminal block TB10.
  • NAVIGAT 2100 CDU Type 4995 – this unit.
  • NAVITWIN IV heading management system – can work with two NAVIGAT 2100 gyrocompasses; NAVIGAT 2100 also gives X-rate, Y-rate and Z-rate outputs to it.
  • Heading repeaters (e.g. Sperry 5016), autopilot, radar, ECDIS and other heading users.

Marine & Industrial Applications

  • Bridge operation of the NAVIGAT 2100 fiber-optic gyrocompass
  • Merchant ships, high-speed craft, offshore and naval vessels with NAVIGAT 2100
  • Replacement of a CDU with dark screen, broken keypad or communication fault
  • Spare CDU for fleets running NAVIGAT 2100 systems

sperry marine navigat 2100 cdu 4995-aa nameplate sto 074820

Rear view of the NAVIGAT 2100 CDU – Northrop Grumman nameplate: Sperry Marine STO No 074820, Type 4995-AA, REV C, D-sub connector and earth stud

Common Problems & Troubleshooting

  • Screen dark or very dim – press DIM+, check supply and cable to the CDU; if still dark, the backlight or LCD may be faulty.
  • Keys do not respond – the membrane keypad may be worn or the keypad connection loose.
  • No data / communication fault – check the rear D-sub connector, cable and the IPSU.
  • System does not enter normal mode after restart – speed and position data must be confirmed at the CDU after alignment.
  • Heading not yet reliable – wait until alignment is complete before using the heading for autopilot, radar or ECDIS.

Safety note: when the IPSU AC supply is on, live voltage is present at TB9, FL1 and TB10. Switch off and isolate power before servicing. Use a magnetic heading source only if the gyrocompass fails.

Maintenance Tips

  • Keep the front panel clean and dry; clean the screen with a soft cloth only.
  • Check the rear connector and earth stud are tight.
  • Note the alarm history and settings before replacing a CDU.
  • Keep a spare CDU on board for quick change.

Spare Parts & Replacement Availability

SM MARINE SERVICE™ supplies the Sperry Marine NAVIGAT 2100 CDU 4995-AA refurbished and can source other NAVIGAT 2100 parts. For a quotation, send the nameplate photo (Type and STO No.), the system serial number if known, your delivery port and the vessel name.

Worldwide Supply & Shipping

We ship gyrocompass spares to ships and agents in the Middle East (Dubai, Fujairah, Jeddah, Doha), Europe (Piraeus, Rotterdam, Hamburg, Istanbul), Asia (Singapore, Shanghai, Busan, Mumbai) and the Americas (Houston, Panama, Santos). African ports such as Lagos, Durban and Mombasa are served by express courier.

Why This Equipment Is Still Used

The NAVIGAT 2100 fiber-optic gyrocompass has no moving parts, so the sensor is long-lasting. When only the CDU fails, changing the CDU keeps the full system working at a fraction of the cost of a new gyrocompass.

FAQ

Q: What is the Sperry Marine NAVIGAT 2100 CDU 4995-AA?
A: It is the Control and Display Unit of the NAVIGAT 2100 fiber-optic gyrocompass.

Q: What is the STO number of this unit?
A: STO No. 074820, Type 4995-AA, REV C.

Q: Which manual covers the CDU type 4995?
A: The NAVIGAT 2100 Operation, Installation and Service Manual 056294.

Q: What other units are in a NAVIGAT 2100 system?
A: The fiber-optic sensor unit and the IPSU (Interface and Power Supply Unit).

Q: Do you know the PCB numbers inside the CDU?
A: Board numbers are not published; send us your board label photo and we will check.

Q: Can the CDU be used with NAVITWIN IV?
A: Yes, NAVITWIN IV can manage two NAVIGAT 2100 gyrocompass systems.

Q: Why does the NAVIGAT 2100 not start normal operation?
A: After each alignment the operator must confirm speed and position at the CDU.

Q: What do the DIM keys do?
A: DIM– and DIM+ change the screen brightness.

Q: Is this unit new?
A: It is supplied refurbished.

Q: What do you need for a quotation?
A: Nameplate photo, delivery port and vessel name.

Short Product Description

Refurbished Sperry Marine NAVIGAT 2100 CDU, Type 4995-AA, STO No. 074820, REV C. This Control and Display Unit is the operator panel of the NAVIGAT 2100 fiber-optic gyrocompass and attitude reference system, used together with the sensor unit and the IPSU. It has an LCD screen, three soft keys, ACK, MENU, arrow and ENTER keys, F1–F3 function keys and DIM keys, with a multi-pin D-sub connector on the rear. It is used for heading display, alarm acknowledgement, alignment confirmation and setup. SM MARINE SERVICE™ ships worldwide – send your nameplate photo for a quotation.

Related Sperry Marine Gyrocompass Equipment – In Stock at SM MARINE SERVICE™

SM MARINE SERVICE™ – Marine Automation & Navigation Equipment Supplier

Available Equipment Conditions: New • Used • Refurbished • Reconditioned (Specific product condition and availability are subject to confirmation.)

Stock Locations: Bangladesh • China

Services: Worldwide Shipping • Technical Support • Spare Parts Supply • Marine Equipment Sourcing

Samir Market, DT Road, Pahartali, beside CDA Market, Chattogram, Bangladesh

Mobile / WhatsApp / Viber: +88 01818 929292

Email: info@smmarineservice.com

Website: https://www.smmarineservice.com/

Send us your nameplate photo, delivery port and vessel name – we will reply quickly with a quotation.


Related products

JRC ECHO SOUNDER MODEL: JFE 582

BDT 0

JRC ECHOSOUNDER JFE-380

BDT 0

JRC ECHO SOUNDER JFE 582

BDT 0

Furuno Voyage Data Recorder (SVDR) VR-3000S

BDT 0

SM Marine Service

SM Marine Service

Marine Equipment Supplier

Welcome to SM Marine Service! How can we help you today? 10:50 PM
Need Help? Chat with us